China best 15kw Screw Air Compressor 8bar 80 Cfm 220 Voltage Silence Vertical Air Compressor set screw bearing shaft tolerance

Product Description

 Permanent-Magnet Variable Frequency Screw Compressor

♦ Intelligent Touch-Screen Design

♦ Direct-driven

♦ Air Cooling

♦ Oil Filter

♦ Air Filter 

♦ Stainless Steel

♦ Piping Design

 

Product features
One shaft-type structure
1. Permanent magnet motor and air-end use the embedded integrated Shaft connecting structure, more compact, 100% transmission Efficiency.
2. No motor bearings, eliminating the motor bearing fault points. Different speeds, permanent magnet
 
 
motor with high efficiency, Remarkable energy-saving effect
1. At the rated speed point, permanent magnet motor efficiency is higher Than ordinary motors.
2. Under low motor speed, a permanent magnet motor can still keep high Motor efficiency. If the gas consumption is less, it still keeps extremely High efficiency. Compared with common frequency conversion
3: Motor, the motor efficiency appears obvious gap and the air Compressor has effective energy saving
It has an integrated structure, configuration of high-efficiency Permanent magnet motor, small size, saving space, and easy disassembly. Deploying an efficient permanent magnet variable frequency controller, it Small volume, low noise Can change the speed of the permanent magnet motor according to The exhaust volume, it will achieve lower operation noise than ordinary Ones.
4. Permanent magnet motor has high-performance NdFeB permanent Magnet, 120 º C without loss of excitation, and service life of over 15 Years.
5. Stator coil adopts special inverter corona resistant enameled wire. Insulation performance and longer service life.
6. Realizing soft start, the motor current will not exceed the full load Current during operation, and greatly reduce the impact on network Equipment, with no damage to electrical equipment.OSG-EZV series permanent magnet compressor Stable operation.

Energy-saving advantages:
a. Permanent magnet motor has high-performance NdFeB permanent Magnet, 120 º C without loss of excitation, and service life of over 15 Years.
b. Stator coil adopts special inverter corona resistant enameled wire. Insulation performance and longer service life.
c. Realizing soft start, the motor current will not exceed the full load Current during operation, and greatly reduce the impact on network Equipment, no damage to electrical equipment.OSG-EZV series permanent magnet compressor
Energy-saving advantages:
 
Condition energy saving
1: The permanent magnet motor remains high efficiency at low speeds, ensuring Obvious energy-saving advantages in small air volumes.
2: Frequency range from 0%-100% (common conversion from 60%-100%)
3: Compared with the fixed speed compressor, energy saving 22%-40%
4: Compared with the common inverter compressor, energy saving 5%-15%
5: System volume fluctuations larger, then energy-saving effect more obvious.
6: Energy saving system of unloading (inverter):
According to the stationary air compressors in gas consumption fluctuation, it has the unloading time, then the air compressor idling but also need 45% of the Electricity, but the permanent-magnet frequency air compressor will control for Inverter, no unloading and no waste. If the air compressor units become larger,
Energy saves more. Save the wasted electric energy by pressure control bandwidth (energy saving):
The fixed compressor must set a minimum control pressure for the 1Barg band (i. E. Air Compressor limits) to avoid the impact on the unit and the power grid. Several Machines must use together with a pressure gradient, more wide pressure, while the OSG permanent-magnet variable-frequency Air compressor series is inverter control, Unlimited stop, no need to set pressure, but a pressure point on the line. With the pressure Of each 0.14Barg bandwidth, the system can save energy by 1%.
 
Energy saving startup (inverter):
The Air compressor’s starting current is 3-6 times the rated current, the frequent Start will waste a lot of energy, and the frequency conversion type has no frequent Starting and stopping, but a soft start. The maximum current does not exceed the rated working current, no energy waste. At the same time also greatly reduce the impact on network equipment, and no damage to electrical equipment OSG company has obtained a compressor production license(certificate NO: XK06-571-0571), has obtained a quality system certificate, and a general machinery certificate. Product design, Manufacturing processes are strict in accordance with ISO9001: 2008 quality system standards

Permanent magnet motor

Synchronous motor with permanent magnet and frequency

converter without any bearing, elastic coupling, or sealing washer.

Eliminate wear, leakage, and replacement.

Variable speed drive

Variable capacity, controlled cost.

The life cycle cost of the compressor can be reduced by 22% on

average.

State-of-the-art screw components

The material of the rotor is special steel.

Advanced wear-resistant bearings.

The rotating screw comes standard with oversized to achieve the

highest efficiency.

Intelligent controller

Increased reliability: durable keyboard, user-friendly, multilingual

user interface.

Improved ease of use: an intuitive navigation system with main

operation conditions include warning indications, maintenance

scheduling etc.

ZheJiang CZPT Gas Compressor Manufacturing Co.,Ltd. founded in 2005, is a leading high technology of machine and equipment manufacturer integrating the design, R&D, production, sales and service for air compressors & Mining Equipment. Adopting advanced technology, design concept and quality control, and we are CZPT to provide customized products to meet customers’ OEM needs.
Our company has more than 520 employees, including 86 senior technicians and professional engineers. Our technical team provides our customers with professional air system solutions. With the total 15000 square meters of the facility, 4 modern advanced production lines are built up to ensure production capacity to meet customer requirements.
Our company has been awarded the honorary title of “ZheJiang high-tech enterprise” and our products enjoy high honors in the industry. Our company has the ISO9001 certification and was awarded the qualification certificate of equipment through military contracts in 2018.
We offer the following products and services:
1. Screw air compressor
    1.1 Oil-free screw air compressor
    1.2 Oil-injected air compressor
2. Reciprocating piston air compressor
    2.1 Piston air compressor
    2.2 Oil-free piston air compressor
    2.3 Piston medium & high-pressure air compressor
3. Portable air compressor & Mining Equipment
    3.1 Diesel or Electric portable screw air compressor
    3.2 Air Pick, Rock Drill, DTH Drilling Rig, Crawler Drilling Rig
4. Air compressor accessories
    4.1 CZPT or Adsorption compressed air drier
    4.2 Compressed air filter or tank
    4.3 Lubrication oil
We have a complete system of after-sales service and quality assurance. The company’s material purchase, inspection, manufacturing, installation, and testing are strictly in accordance with the ISO procedures. which will ensure each compressor has reliable quality and has a complete record to trace if needed.

Q: Do you test all your goods before delivery?
A: Yes, we have 100% test before delivery.

Q: How can we start ordering with your factory?
A: First, leave us an inquiry and advise which item you’re interested in, and then we will contact you within 24 hours. You’re so kind if provide all the detailed information, will be better for us to know exactly what you need.

Q: What is your MOQ?
A: Different products have different MOQs, most are 1 set.

Q: What are your terms of payment?
A: T/T 30% as deposit, and 70% before delivery. We’ll show you the photos of the products and packages.

Q: How about your delivery time?
A: Generally, it will take 90 days after receiving your advance payment. The specific delivery time depends on the items and the quantity of your order.

Q: Do you have a trading company or a real factory?
A: We are a 100% factory; we are located in ZheJiang city, China.

After-sales Service: Online Support
Warranty: 1 Years
Lubrication Style: Lubricated
Cooling System: Air Cooling
Power Source: AC Power
Structure Type: Closed Type
Samples:
US$ 1500/Piece
1 Piece(Min.Order)

|
Request Sample

Customization:
Available

|

Customized Request

screwshaft

Screw Shaft Types

A screw shaft is a cylindrical part that turns. Depending on its size, it is able to drive many different types of devices. The following information outlines the different types of screws, including their sizes, material, function, and applications. To help you select the right screw shaft, consider the following factors:

Size

A screw can come in a variety of shapes and sizes, ranging from a quarter to a quarter-inch in diameter. A screw is a cylindrical shaft with an inclined plane wrapped around it, and its main function is to fasten objects together by translating torque into a linear force. This article will discuss the dimensions of screws and how to determine the size of a screw. It is important to note that screw sizes can be large and small depending on the purpose.
The diameter of a screw is the diameter of its shaft, and it must match the inner diameter of its nuts and washers. Screws of a certain diameter are also called machine screws, and they can be larger or smaller. Screw diameters are measured on the shaft underneath the screw head. The American Society of Mechanical Engineers (ASME) standardized screw diameters in 3/50-inch to 16 (3/8-inch) inches, and more recently, sizes were added in U.S. fractions of an inch. While shaft and head diameters are standardized, screw length may vary from job to job.
In the case of the 2.3-mm screw group, the construct strength was not improved by the 1.2-mm group. The smaller screw size did not increase the strength of the construct. Further, ABS material did not improve the construct strength. Thus, the size of screw shaft is an important consideration in model design. And remember that the more complex your model is, the larger it will be. A screw of a given size will have a similar failure rate as a screw of a different diameter.
Although different screw sizes are widely used, the differences in screw size were not statistically significant. Although there are some limitations, screws of different sizes are generally sufficient for fixation of a metacarpal shaft fracture. However, further clinical studies are needed to compare screw sizes for fracture union rates. So, if you are unsure of what size of screw shaft you need for your case, make sure to check the metric chart and ensure you use the right one.
screwshaft

Material

The material of a screw shaft plays an important role in the overall performance of a screw. Axial and central forces act to apply torque to the screw, while external forces, such as friction, exert a bending moment. The torsional moments are reflected in the torque, and this causes the screw to rotate at a higher rate than necessary. To ensure the longevity of the screw, the material of the screw shaft should be able to handle the bending moment, while the diameter of the shaft should be small enough to avoid causing damage.
Screws are made from different metals, such as steel, brass, titanium, and bronze. Manufacturers often apply a top coating of chromium, brass, or zinc to improve corrosion resistance. Screws made of aluminum are not durable and are prone to rusting due to exposure to weather conditions. The majority of screw shafts are self-locking. They are suited for many applications, including threaded fasteners, C-clamps, and vises.
Screws that are fabricated with conical sections typically feature reduced open cross-sectional areas at the discharge point. This is a key design parameter of conical screw shafts. In fact, reductions of up to 72% are common across a variety of applications. If the screw is designed to have a hard-iron hanger bearing, it must be hardened. If the screw shaft is not hardened, it will require an additional lubricant.
Another consideration is the threads. Screw shafts are typically made of high-precision threads and ridges. These are manufactured on lathes and CNC machines. Different shapes require different materials. Materials for the screw shaft vary. There are many different sizes and shapes available, and each one has its own application. In addition to helical and conical screw shafts, different materials are also available. When choosing material, the best one depends on the application.
The life of the screw depends on its size, load, and design. In general, the material of the screw shaft, nut body, and balls and rollers determine its fatigue life. This affects the overall life of the screw. To determine whether a specific screw has a longer or shorter life, the manufacturer must consider these factors, as well as the application requirements. The material should be clean and free of imperfections. It should be smooth and free of cracks or flaking, which may result in premature failure.

Function

The function of a screw shaft is to facilitate the rotation of a screw. Screws have several thread forms, including single-start, double-start and multi-start. Each form has its own advantages and disadvantages. In this article we’ll explore each of them in detail. The function of a screw shaft can vary based on its design, but the following are common types. Here are some examples of screw shaft types and their purposes.
The screw’s torque enables it to lift objects. It can be used in conjunction with a bolt and nut to lift a load. Screws are also used to secure objects together. You can use them in screw presses, vises, and screw jacks. But their primary function is to hold objects together. Listed below are some of their main functions. When used to lift heavy loads, they can provide the required force to secure an object.
Screws can be classified into two types: square and round. Square threads are more efficient than round ones because they apply 0deg of angle to the nut. Square threads are also stronger than round threads and are often used in high-load applications. They’re generally cheaper to manufacture and are more difficult to break. And unlike square threads, which have a 0deg thread angle, these threads can’t be broken easily with a screwdriver.
A screw’s head is made of a series of spiral-like structures that extend from a cylindrical part to a tip. This portion of the screw is called the shank and is made of the smallest area. The shank is the portion that applies more force to the object. As the shaft extends from the head, it becomes thinner and narrow, forming a pointed tip. The head is the most important part of the screw, so it needs to be strong to perform its function.
The diameter of the screw shaft is measured in millimeters. The M8 screw has a thread pitch of 1.25 mm. Generally, the size of the screw shaft is indicated by the major and minor diameter. These dimensions are appended with a multiplication sign (M8x1).
screwshaft

Applications

The design of screws, including their size and shape, determines their critical rotating speeds. These speeds depend on the threaded part of the screw, the helix angle, and the geometry of the contact surfaces. When applied to a screw, these limits are referred to as “permissible speed limits.” These maximum speeds are meant for short periods of time and optimized running conditions. Continuous operation at these speeds can reduce the calculated life of a nut mechanism.
The main materials used to manufacture screws and screw shafts include steel, stainless steel, titanium, bronze, and brass. Screws may be coated for corrosion resistance, or they may be made of aluminium. Some materials can be threaded, including Teflon and nylon. Screw threads can even be molded into glass or porcelain. For the most part, steel and stainless steel are the most common materials for screw shafts. Depending on the purpose, a screw will be made of a material that is suitable for the application.
In addition to being used in fasteners, screw shafts are used in micrometers, drillers, conveyor belts, and helicopter blades. There are numerous applications of screw shafts, from weighing scales to measuring lengths. If you’re in the market for a screw, make sure to check out these applications. You’ll be happy you did! They can help you get the job done faster. So, don’t delay your next project.
If you’re interested in learning about screw sizing, then it’s important to know the axial and moment loads that your screws will experience. By following the laws of mechanics and knowing the load you can calculate the nominal life of your screw. You can also consider the effect of misalignment, uneven loading, and shocks on your screw. These will all affect the life of your screw. Then, you can select the right screw.

China best 15kw Screw Air Compressor 8bar 80 Cfm 220 Voltage Silence Vertical Air Compressor   set screw bearing shaft toleranceChina best 15kw Screw Air Compressor 8bar 80 Cfm 220 Voltage Silence Vertical Air Compressor   set screw bearing shaft tolerance
editor by CX 2023-04-20